For 2003-2007 Honda Accord Replacement CU2797 Aluminum Radiator
OE design to ensure exact fit, form and function for an easy drop-in installation. Built with high density multi-lowered fins for maximum cooling efficiency. ISO 9001 certified manufacturing plants. Plastic tanks with aluminum core. Built to strict quality control standards. How to clean radiator. Step 1: Let the Radiator Cool Down. Step 2: Dilute the Cleaning Solution. Step 3: Clean the Radiator Fins With the Solution and Soft-Bristled Brush. Step 4: If Some Radiator Fins Get Bent, Straighten With a Flathead Screwdriver. Step 5: Rinse the Radiator Fins With a Hose. Step 6: Let the Radiator Fins Air Dry. Step 1: Let the Engine Cool Down. Step 2: Put a Catch Pan or Bucket Underneath the Radiator. Step 3: Drain Out the Coolant. Step 4: Dilute the Flushing Solution. Step 5: Pour the Flushing Solution Into the Radiator. Step 6: Drain Out the Flushing Solution. Step 7: Pour Distilled Water Into the Radiator. Step 8: Refill Coolant Into the Radiator. Step 9: Monitor the Cooling System and Resolve Issues. How to replace the radiator. Remove the air duct and disconnect the negative battery cable. Take off the air cleaner assembly, and drain the cooling system into a resealable container. Take off the radiator’s inlet hose and remove the transmission’s cooler lines. Take off the fan shroud clips on the condenser tubes, and remove the bolts that connect the fan shroud to the condenser bracket. Remove the air deflectors. Disconnect the coolant hose from the radiator overflow and take off the radiator support brackets on the fan shroud. Disconnect the electrical connectors on the engine cooling fan motor, and remove the fan motor harness from the fan shroud clips. Remove the fan shroud. Take off the radiator’s outlet hose and disconnect the transaxle oil cooler pipes. Tile the radiator towards the rear and remove the condenser brackets. Lift the condenser brackets and the mounting tabs and position them out of the way. Lift the radiator carefully out of the engine compartment and install the new radiator. Reinstall and reconnect the engine components in the reverse order that they were removed. Fill the new radiator with a mixture of half water and half engine coolant. Start the engine and let it run for a couple of minutes, then turn it off and add more fluids, if necessary. Reattach the negative battery cable. Engine coolant can be reused if it isn’t old or contaminated. However, if you choose not to reuse it, take it to a garage or a hazardous waste facility for proper disposal. To avoid scalds, wear gloves and protective clothing before changing the radiator, and always be sure the engine is cool before replacing the radiator. Be sure to keep engine coolant in a sealed container out of the reach of children and pets. If any is spilled, clean it up immediately. 1pc of brand new radiator. 2797 radiator, new, cooling radiator, air radiator. 2797 radiator, Engine Rad, Replacement Radiator. 2797 radiator, RAD2797, CU2797, DPI2797, Aluminum. Please verify the item fits your vehicle or not by compatibility. Engine Oil Cooler Included. Transmission Oil Cooler Included. The note there will NOT be read. The images shown are not the actual item and are for your reference only. There are NO EXCEPTIONS! OR, you may choose to have a replacement. FEEDBACK IS VERY IMPORTANT TO US. It is impossible to address issues if we do not know about them! For 99-16 Ford Super Duty 2-Row LED Rear Third 3RD Tail Brake Light Stop Lamp. LED Third 3rd Brake Light For 93-11 Ford Ranger 99-16 F250 F350 F450 Super Duty. BLACK HOUSING FOR 97-07 DODGE DAKOTA LED REAR THIRD 3RD TAIL BRAKE LIGHT LAMP. Front Headlamp Assembly Reflector Headlights Assembly for 98-02 Honda Accord. For 11-18 Dodge Charger Jeep Grand Cherokee Chrysler 300 Water Pump 5.7L 6.4L. For 95-05 Mercury Sable 3.0L V6 OHV VIN U Engine Water Pump W/ Gasket CWP-9038. For 05-10 Chrysler 300 3.5L 06-10 Dodge Charger 3.5L Water Pump W/ Gasket CP6010.